dimensions in inches (millimeters) and are subject to change without notice. ? 2008 glenair, inc. cage code 06324 printed in u.s.a. glenair, inc. ? 1211 air way ? glendale, ca 91201-2497 ? 818-247-6000 ? fax 818-500-9912 www.glenair.com d-1 e-mail: sales@glenair.com series 79 micro-crimp section d: cable connectors, crimp termination a a b b c c d d e e f f g g h h index index cable connectors cable recept acles with pin cont acts, crimp termina tion, 790-024p how t o order sample part number 790-024p c-13 m p base part number shell size - insert arr. shell finish hardware option 790-024p cable receptacle with pin contacts see table 1 for available insert arrangements . to order a connector without size #16 or #12 power pins, substitute w instead of p in the insert arrangement. example: 36p2 is supplied with 2 power pins. 36w2 is supplied less the power pins. see section b for coaxial contacts purchased separately. m electroless nickel general purpose applications mt nickel-ptfe 1000 hour grey? maximum corrosion protection and durability (non-refective grey) znu zinc-nickel with black chromate tactical applications (non-refective black) additional shell fnishes are listed on page c-9. n thru-hole no hardware actual size p female jackpost actual size l low-profle captivated jackscrew, hex head actual size k slot-head extended jackscrew actual size s low-profle captivated screwlock, hex head actual size t slot-head extended captivated screwlock s pecifications current rating #23 5 amps, #16 13 a., #12 23 a. dielectric withstanding voltage #23 500 vac rms, #12 and #16 1800 vac rms insulation resistance 5000 megohms minimum operating temperature -65 c. to +150 c. shock 300 g. vibration 37 g. m aterials and finishes shell aluminum alloy contacts copper alloy, 50 microinches g old plated insulators liquid crystal polymer (lcp) retention clips beryllium copper alloy interfacial seal, grommet flourosilicone rubber hardware 300 series stainless steel rugged, lightweight 790-024p connectors feature machined aluminum shells, fuorosilicone face seals and wire grommets for environmental protection. contacts are rear-release snap-in crimp type. connectors are supplied with crimp contacts packaged separately. size #23 signal pins accept up to #22 awg wire. size #16 contacts accept #16-18 awg wire. size #12 contacts accept #12-14 awg wire. size 12 and 16 cavities also accept coaxial contacts purchased separately. connector shell features a groove for attachment of a low-profle emi backshell adapter 799-015, ordered separately. rev. 01-aug-2008
dimensions in inches (millimeters) and are subject to change without notice. ? 2008 glenair, inc. cage code 06324 printed in u.s.a. glenair, inc. ? 1211 air way ? glendale, ca 91201-2497 ? 818-247-6000 ? fax 818-500-9912 www.glenair.com d-2 e-mail: sales@glenair.com cable connectors series 79 micro-crimp section d: cable connectors, crimp termination a a b b c c d d e e f f g g h h index index a a b b c c d d e e f f g g h h index index shell groove for emi adapter pin contact interfacial seal front insulator retaining clip rear insulator grommet potting wire (ref.) cross-sectional view of 790-024p table 1 contact arrangements layout contact quantity face view #23 #16 #12 a-5 5 b-2p2 2 b-9 9 c-13 13 d-15 15 d-3p3 3 d-7p2 5 2 e-11p2 9 2 e-19 19 e-7p3 4 3 f-15p2 13 2 f-23 23 f-5p5 5 g-33 33 h-10p4 6 4 h-29p7 22 7 h-36p2 34 2 h-54p2 52 2 h-5p5 5 h-66 66 j-17p4 13 4 j-25p2 23 2 j-33 33 j-7p7 7 k-27p4 23 4 k-35p2 33 2 k-43 43 k-9p9 9 l-6p6 6 t able 2 h ardware option actual size .190 (4.83) max n no mating hardware connector is supplied with thru-holes. shell sizes h and l are .148" (3.76) diameter, other shell sizes are .092" (2.34) diameter. accepts standard micro-d m83513 hardware. p jackposts connector is supplied with removable jackposts. shell sizes h and l have #4-40 unc thread, other sizes have #2-56 thread. stainless steel. conforms to m83513/05. actual size .155 (3.94) max actual size .925 (23.5) max l hex head jackscrews connector is supplied with stainless steel non- removable low profile jackscrews. shell sizes h and l have #4-40 unc thread, other sizes have #2-56 thread. k extended jackscrews connector is supplied with stainless steel slot head non-removable jackscrews. shell sizes h and l have #4-40 unc thread, other sizes have #2-56 thread. actual size .290 (7.37) max actual size .925 (23.50) max s hex head screwlocks connector is supplied with stainless steel non- removable low profile screwlocks. shell sizes h and l have #4-40 unc thread, other sizes have #2-56 thread. screwlocks allow the connector to be mated before the screws are fastened. t extended screwlocks connector is supplied with stainless steel non- removable slot head screwlocks. shell sizes h and l have #4-40 unc thread, other sizes have #2-56 thread. screwlocks allow the connector to be mated before the screws are fastened. rev. 01-aug-2008
a a b b c c d d e e f f g g h h index index dimensions in inches (millimeters) and are subject to change without notice. ? 2008 glenair, inc. cage code 06324 printed in u.s.a. glenair, inc. ? 1211 air way ? glendale, ca 91201-2497 ? 818-247-6000 ? fax 818-500-9912 www.glenair.com d-3 e-mail: sales@glenair.com series 79 micro-crimp section d: cable connectors, crimp termination a a b b c c d d e e f f g g h h index index cable connectors 790-024p d imensions shell size h and l shell size g shell sizes a, b, c, d, e, f, j, k 1 16 50 66 33 49 17 34 e max h max f basic g max .152/.145 (3.86/3.68) dia 2 places .195 .003 (4.95 0.08) .093 .005 (2.36 0.13) .410 (10.41) max .760 (19.30) max .096/.088 (2.44/2.24) dia 2 places .395 (10.03) max .195 .003 (4.95 0.08) .093 .005 (2.36 0.13) .760 (19.30) max 1.055 (26.80) max 1.435 (1.80) max 1.215 (30.86) basic 1.079 (27.41) max a max .096/.088 (2.44/2.24) dia 2 places .308 (7.82) max .195 .003 (4.95 0.08) .093 .005 (2.36 0.13) .760 (19.30) max b basic c max d max groove for attachment of emi adapter 799-015 790-024p d imensions shell size a max. b basic c max. d max. e max. f basic g max. h max. in. mm. in . mm. in. mm. in. mm. in. mm. in. mm. in. mm. in. mm. a .785 19.94 .565 14.35 .400 10.16 .390 9.91 b .935 23.75 .715 18.16 .551 14.00 .540 13.72 c 1.085 27.65 .865 21.97 .701 17.81 .690 17.53 d 1.185 30.10 .965 24.51 .801 20.35 .790 20.07 e 1.335 33.91 1.115 28.32 .951 24.16 .940 23.88 f 1.485 37.72 1.265 32.13 1.101 27.96 1.090 27.69 h 2.175 55.25 1.800 45.72 1.450 36.83 1.440 36.58 j 1.845 46.86 1.615 41.02 1.460 37.08 1.450 36.83 k 2.240 56.90 2.015 51.18 1.860 47.24 1.840 46.74 l 2.420 61.47 2.036 51.71 1.686 42.82 1.675 42.55 rev. 01-aug-2008
|